Search Fire Alarm Questions for "MS-9200" | Fire Alarm Resource Center

How do I perform a walk test on the MS-9200UDLS?

To perform a walk test on the MS-9200UDLS, navigate to the Walktest menu through either the Programming or Maintenance screens and select between a silent or...

Fire-Lite MS-9200UDLSAnswered3mo ago95 views

What are the key differences between the MS-9600 and the MS-9200UDLS?

The MS-9600 supports up to 636 points and uses LiteSpeed polling, while the MS-9200UDLS is a smaller panel with different electrical requirements. Key...

Fire-Lite MS-9600Answered3mo ago56 views

How do I add a remote annunciator to the MS-9200UDLS?

To add a remote annunciator such as the ANN-80, you must wire the device to the FACP's ANN-BUS terminals, assign a unique address using the module's DIP...

Fire-Lite MS-9200UDLSAnswered3mo ago64 views

How do I wire a 4-wire smoke detector to the MS-9200UDLS?

To wire a 4-wire smoke detector, connect the detector's power terminals to the Resettable Power output (TB1 terminals 3 and 4), which provides 24 VDC filtered...

Fire-Lite MS-9200UDLSAnswered3mo ago52 views

What batteries does the MS-9200UDLS use, and when is an external battery cabinet required?

The MS-9200UDLS uses sealed lead-acid batteries with a minimum capacity of 7 AH (Page 15) [1]. The standard control panel cabinet is designed to house and...

Fire-Lite MS-9200UDLSAnswered3mo ago59 views

What does INVREP trouble mean on the MS-9200UDLS and how do I resolve it?

INVREP indicates an invalid reply from an addressable device, which typically points to a hardware or communication problem (Page 131, 136) [1]. This...

Fire-Lite MS-9200UDLSAnswered3mo ago167 views

How do I program the MS-9200UDLS — can it be done from the front panel or is PS-Tools required?

The MS-9200UDLS is completely field programmable from the front panel keypad and does not require PS-Tools software for setup (Page 65) [1]. You can also...

Fire-Lite MS-9200UDLSAnswered3mo ago52 views

What are the NAC circuit specifications for the MS-9200UDLS?

The MS-9200UDLS features four onboard Notification Appliance Circuits (NACs) that provide 24 VDC nominal special application power (Page 15) [1]. Each circuit...

Fire-Lite MS-9200UDLSAnswered3mo ago59 views

What is the maximum device capacity on the MS-9200UDLS SLC, and what is the difference between CLIP and LiteSpeed mode?

The MS-9200UDLS has a maximum capacity of 198 addressable devices, consisting of 99 detectors and 99 control or monitor modules (Page 91) [1]. LiteSpeed is the...

Fire-Lite MS-9200UDLSAnswered3mo ago64 views

What does UDLS mean on the MS-9200UDLS and how does the built-in communicator work?

The UDLS suffix indicates the panel supports Upload/Download (UD) capabilities and utilizes the LiteSpeed (LS) polling protocol for faster device response...

Fire-Lite MS-9200UDLSAnswered3mo ago77 views

How do I troubleshoot a ground fault on the MS-9200UDLS?

To troubleshoot a ground fault, identify the condition by the flashing yellow Ground Fault LED, which indicates zero impedance from the FACP to ground (Page...

Fire-Lite MS-9200UDLSAnswered3mo ago87 views

How do I troubleshoot a Loop Fault or SLC Communication Failure on the MS-5024?

The MS-5024 is a conventional panel and does not utilize an SLC (Signaling Line Circuit) or addressable loop; those features are found on addressable panels...

Fire-Lite MS-5024Answered3mo ago73 views

Search Results for "MS-9200"