Search Fire Alarm Questions for "iO1000" | Fire Alarm Resource Center

How do I address devices on the iO1000?

The iO1000 uses electronic addressing for all Addressable Signature series devices, meaning there are no physical dip switches or rotary dials to set on the...

Edwards Est IO1000Answered2mo ago112 views

How do I connect the iO1000 to an SA-ETH Ethernet card for remote monitoring or network annunciation?

The SA-ETH card connects to the iO1000 main circuit board at connector J1 and provides a 10/100 Base-T connection for remote diagnostics, iO-CU programming,...

Edwards Est IO1000Answered3mo ago58 views

What are the iO1000 auxiliary power output ratings for powering external 24VDC devices?

The iO1000 provides two auxiliary power outputs, Aux 1 and Aux 2, each rated at 500 mA at 24 VDC nominal (Page 4) [1]. Aux 1 is a continuous circuit typically...

Edwards Est IO1000Answered3mo ago65 views

How do I program zone mapping and custom label text on the iO1000 using the front-panel LCD menu?

To enable Mapping, navigate to Menu > Programming > Advanced Program (enter Level 2 password) > Loop Configuration > Mapping, then select the loop and set it...

Edwards Est IO1000Answered3mo ago53 views

What are the key differences between the iO64 and iO1000 beyond device capacity?

The iO1000 provides double the standard notification circuits and significantly higher power (6.0 A vs 3.75 A) compared to the iO64 (Page 6) [1]. It also...

Edwards Est IO1000Answered3mo ago55 views

How do I set up the SA-DACT dialer module in the iO1000 for dual-line DACT reporting using Contact ID format?

Install the SA-DACT module and connect it to the main board via the ribbon cable at J8. In the panel's programming menu, set the CMS device type to Dual Line...

Edwards Est IO1000Answered3mo ago95 views

What Signature series devices are compatible with the iO1000 SLC loop, and can I mix legacy and newer devices on the same loop?

The iO1000 is compatible with the entire Signature Series family of intelligent devices, including multi-sensor smoke, heat, and 10-year carbon monoxide (CO)...

Edwards Est IO1000Answered3mo ago81 views

What version of the IO-CU configuration utility is required for the iO1000, and can I upload programming via the SA-ETH Ethernet card?

I couldn't find a specific version number for the iO-CU utility in the manuals, which only specify using "compatible iO-CU software" (Page 2) [1]. Yes, you can...

Edwards Est IO1000Answered3mo ago80 views

How do I configure the iO1000 NAC circuits for Class A wiring instead of the default Class B?

The iO1000 is Class A Ready and does not require an expansion card for Class A wiring (Page 6) [1]. To configure this, you must program the NACs in pairs (one...

Edwards Est IO1000Answered3mo ago79 views

What is the correct procedure for isolating and clearing a ground fault on the iO1000 SLC loop versus a NAC ground fault?

To isolate an iO1000 SLC loop ground fault, use the Fast Ground Check tool in the panel menu to increase the testing frequency (Page 216) [3]. If the LCD...

Edwards Est IO1000Answered3mo ago74 views

How do I expand the iO1000 from 250 to 1,000 addressable points using iO-SDC1 and iO-SDC2 loop cards?

To expand the iO1000 to its 1,000-point maximum, you must install two iO-SDC2 dual loop controller cards into the panel's expansion slots (Page 3, 25) [1]....

Edwards Est IO1000Answered3mo ago53 views

What are the differences between the iO64 and iO1000?

The primary differences between the iO64 and iO1000 involve device capacity, notification circuit (NAC) configuration, and expansion options. | Feature | iO64...

Edwards Est IO64Answered3mo ago55 views

Search Results for "iO1000"