FACP
Manuals
Resource Center
Tools
Ask AI
Sign In
Ask AI
Sign In
Home
Loading…
FACP
Manuals
Resource Center
Tools
Ask AI
Sign In
Ask AI
Sign In
Home
Resources
Trouble Codes
Edwards Est
Io1000
200
Resource Center
Browse
Home
Questions
258
Trouble Codes
672
Panels
24
Panel Specs
24
Learn
NFPA 72-2025
Community
Community Wall
Tools
Ask AI
Loading…
Resource Center
Browse
Home
Questions
258
Trouble Codes
672
Panels
24
Panel Specs
24
Learn
NFPA 72-2025
Community
Community Wall
Tools
Ask AI
FACP
Manuals
Resource Center
Tools
Ask AI
Sign In
Ask AI
Sign In
Home
•••
Resources
Trouble Codes
Edwards Est
Io1000
200
Sign In
Supervisory active: iO1000 Trouble Code | Fire Alarm Resource Center
Supervisory active
supervisory
Edwards EST iO1000
72 views
What This Code Means
A supervisory condition has been activated
Common Causes
1
Sprinkler valve tamper switch moved
2
Duct detector housing opened
3
Pressure switch activated
Resolution Steps
Locate the supervisory device and restore it to its normal position (e.g., open the water valve or close the tamper switch).
Manual References
(3)
1
edwards est
iO64 and iO1000
Datasheet
2020
p. 1
Open
2
edwards est
iO64 and iO1000
Datasheet
2023
p. 1
Open
3
edwards est
iO64 and iO1000
Installation
2015
p. 186, 160, 61, 187, 189 +2
Open
Getting Supervisory active on your iO1000?
Ask TroubleShooter AI for help
→
Field Notes
Loading field notes...
Sign in
to share a field note
Related Codes
Dialer delivery fail
The dialer failed to deliver a message to the receiver
Internal fault
The control panel detected an internal hardware or software error
Loop 1 map mismatch
The loop 1 map in RAM and the loop 1 map in the database do not match
Dialer line 1 fault
A ground fault or line fault was detected on line 1 of the dialer
001 Loop 1 fault
A short or open was detected on the loop affecting the communications between the panel and the devices on the loop.
Related Questions
How do I address devices on the iO1000?
How do I set up the SA-DACT dialer module in the iO1000 for dual-line DACT reporting using Contact ID format?
What version of the IO-CU configuration utility is required for the iO1000, and can I upload programming via the SA-ETH Ethernet card?
Supervisory active
supervisory
Edwards EST iO1000
72 views
What This Code Means
A supervisory condition has been activated
Common Causes
1
Sprinkler valve tamper switch moved
2
Duct detector housing opened
3
Pressure switch activated
Resolution Steps
Locate the supervisory device and restore it to its normal position (e.g., open the water valve or close the tamper switch).
Manual References
(3)
1
edwards est
iO64 and iO1000
Datasheet
2020
p. 1
Open
2
edwards est
iO64 and iO1000
Datasheet
2023
p. 1
Open
3
edwards est
iO64 and iO1000
Installation
2015
p. 186, 160, 61, 187, 189 +2
Open
Getting Supervisory active on your iO1000?
Ask TroubleShooter AI for help
→
Field Notes
Loading field notes...
Sign in
to share a field note
Related Codes
Dialer delivery fail
The dialer failed to deliver a message to the receiver
Internal fault
The control panel detected an internal hardware or software error
Loop 1 map mismatch
The loop 1 map in RAM and the loop 1 map in the database do not match
Dialer line 1 fault
A ground fault or line fault was detected on line 1 of the dialer
001 Loop 1 fault
A short or open was detected on the loop affecting the communications between the panel and the devices on the loop.
Related Questions
How do I address devices on the iO1000?
How do I set up the SA-DACT dialer module in the iO1000 for dual-line DACT reporting using Contact ID format?
What version of the IO-CU configuration utility is required for the iO1000, and can I upload programming via the SA-ETH Ethernet card?
