FACP
Manuals
Resource Center
Tools
Ask AI
Sign In
Ask AI
Sign In
Home
Loading…
FACP
Manuals
Resource Center
Tools
Ask AI
Sign In
Ask AI
Sign In
Home
Resources
Trouble Codes
Esser
Flexes
Essernet Connection Interruption
Resource Center
Browse
Home
Questions
258
Trouble Codes
672
Panels
24
Panel Specs
24
Learn
NFPA 72-2025
Community
Community Wall
Tools
Ask AI
Loading…
Resource Center
Browse
Home
Questions
258
Trouble Codes
672
Panels
24
Panel Specs
24
Learn
NFPA 72-2025
Community
Community Wall
Tools
Ask AI
FACP
Manuals
Resource Center
Tools
Ask AI
Sign In
Ask AI
Sign In
Home
•••
Resources
Trouble Codes
Esser
Flexes
Essernet Connection Interruption
Sign In
essernet connection interruption: FlexES Trouble Code | Fire Alarm Resource Center
essernet connection interruption
trouble
ESSER FlexES
143 views
What This Code Means
A break or wiring error has been detected in the essernet communication loop.
Common Causes
1
Broken communication wire
2
Interchanged (swapped) connections
3
Loose terminal block connection
Resolution Steps
Check the continuity of the essernet loop and ensure outward and return lines are not interchanged or routed in the same cable duct.
Manual References
(1)
1
esser
FlexES Control
Installation
2010
p. 71, 3, 2, 49, 87 +4
Open
Getting essernet connection interruption on your FlexES?
Ask TroubleShooter AI for help
→
Field Notes
Loading field notes...
Sign in
to share a field note
Related Codes
Panel or essernet device not receiving power
A device on the essernet is not receiving power or is completely disconnected.
Battery Fault
The FACP indicates a fault when battery resistance is too high, voltage drops below the discharging limit, or a connection/fuse issue is detected.
EARTH FAULT
The system has detected an unintended connection to ground or an incorrect configuration of the earth fault detection jumpers on multiple power supply modules.
Wrong address setting
The essernet module has detected an invalid or conflicting address configuration after a restart.
>Short circuit/interruption<
A condition indicating a short circuit or interruption on the connection line, which may cause the system to isolate segments of the loop using group separators.
Related Questions
What do the common FlexES error codes mean, such as Loop Fault, Short Circuit, and Device Not Responding?
How do I reset a fault condition on the Esser FlexES panel after replacing a detector on the loop?
How do I program new esserbus Plus detectors and modules into the FlexES panel using Tools 8000 software?
essernet connection interruption
trouble
ESSER FlexES
143 views
What This Code Means
A break or wiring error has been detected in the essernet communication loop.
Common Causes
1
Broken communication wire
2
Interchanged (swapped) connections
3
Loose terminal block connection
Resolution Steps
Check the continuity of the essernet loop and ensure outward and return lines are not interchanged or routed in the same cable duct.
Manual References
(1)
1
esser
FlexES Control
Installation
2010
p. 71, 3, 2, 49, 87 +4
Open
Getting essernet connection interruption on your FlexES?
Ask TroubleShooter AI for help
→
Field Notes
Loading field notes...
Sign in
to share a field note
Related Codes
Panel or essernet device not receiving power
A device on the essernet is not receiving power or is completely disconnected.
Battery Fault
The FACP indicates a fault when battery resistance is too high, voltage drops below the discharging limit, or a connection/fuse issue is detected.
EARTH FAULT
The system has detected an unintended connection to ground or an incorrect configuration of the earth fault detection jumpers on multiple power supply modules.
Wrong address setting
The essernet module has detected an invalid or conflicting address configuration after a restart.
>Short circuit/interruption<
A condition indicating a short circuit or interruption on the connection line, which may cause the system to isolate segments of the loop using group separators.
Related Questions
What do the common FlexES error codes mean, such as Loop Fault, Short Circuit, and Device Not Responding?
How do I reset a fault condition on the Esser FlexES panel after replacing a detector on the loop?
How do I program new esserbus Plus detectors and modules into the FlexES panel using Tools 8000 software?
