FACP
Manuals
Resource Center
Tools
Ask AI
Sign In
Ask AI
Sign In
Home
Loading…
FACP
Manuals
Resource Center
Tools
Ask AI
Sign In
Ask AI
Sign In
Home
Resources
Trouble Codes
Esser
Flexes
Essernet Line Damage
Resource Center
Browse
Home
Questions
258
Trouble Codes
672
Panels
24
Panel Specs
24
Learn
NFPA 72-2025
Community
Community Wall
Tools
Ask AI
Loading…
Resource Center
Browse
Home
Questions
258
Trouble Codes
672
Panels
24
Panel Specs
24
Learn
NFPA 72-2025
Community
Community Wall
Tools
Ask AI
FACP
Manuals
Resource Center
Tools
Ask AI
Sign In
Ask AI
Sign In
Home
•••
Resources
Trouble Codes
Esser
Flexes
Essernet Line Damage
Sign In
Damaging the line (essernet module 500 kBd): FlexES Trouble Code | Fire Alarm Resource Center
Damaging the line (essernet module 500 kBd)
trouble
ESSER FlexES
83 views
What This Code Means
Physical damage to the essernet 500 kBd line, often due to installation errors.
Common Causes
1
Insufficient bending radii during installation
2
Physical crushing of the cable duct
3
Cable insulation damage
Resolution Steps
Inspect the cable for physical damage or sharp bends; replace the affected section of the cable and ensure proper bending radii.
Manual References
(1)
1
esser
FlexES Control
Installation
2010
p. 71, 3, 2, 49, 87 +4
Open
Getting Damaging the line (essernet module 500 kBd) on your FlexES?
Ask TroubleShooter AI for help
→
Field Notes
Loading field notes...
Sign in
to share a field note
Related Codes
essernet connection interruption
A break or wiring error has been detected in the essernet communication loop.
Panel or essernet device not receiving power
A device on the essernet is not receiving power or is completely disconnected.
Battery Fault
The FACP indicates a fault when battery resistance is too high, voltage drops below the discharging limit, or a connection/fuse issue is detected.
EARTH FAULT
The system has detected an unintended connection to ground or an incorrect configuration of the earth fault detection jumpers on multiple power supply modules.
Wrong address setting
The essernet module has detected an invalid or conflicting address configuration after a restart.
Related Questions
What do the common FlexES error codes mean, such as Loop Fault, Short Circuit, and Device Not Responding?
How do I reset a fault condition on the Esser FlexES panel after replacing a detector on the loop?
How do I program new esserbus Plus detectors and modules into the FlexES panel using Tools 8000 software?
Damaging the line (essernet module 500 kBd)
trouble
ESSER FlexES
83 views
What This Code Means
Physical damage to the essernet 500 kBd line, often due to installation errors.
Common Causes
1
Insufficient bending radii during installation
2
Physical crushing of the cable duct
3
Cable insulation damage
Resolution Steps
Inspect the cable for physical damage or sharp bends; replace the affected section of the cable and ensure proper bending radii.
Manual References
(1)
1
esser
FlexES Control
Installation
2010
p. 71, 3, 2, 49, 87 +4
Open
Getting Damaging the line (essernet module 500 kBd) on your FlexES?
Ask TroubleShooter AI for help
→
Field Notes
Loading field notes...
Sign in
to share a field note
Related Codes
essernet connection interruption
A break or wiring error has been detected in the essernet communication loop.
Panel or essernet device not receiving power
A device on the essernet is not receiving power or is completely disconnected.
Battery Fault
The FACP indicates a fault when battery resistance is too high, voltage drops below the discharging limit, or a connection/fuse issue is detected.
EARTH FAULT
The system has detected an unintended connection to ground or an incorrect configuration of the earth fault detection jumpers on multiple power supply modules.
Wrong address setting
The essernet module has detected an invalid or conflicting address configuration after a restart.
Related Questions
What do the common FlexES error codes mean, such as Loop Fault, Short Circuit, and Device Not Responding?
How do I reset a fault condition on the Esser FlexES panel after replacing a detector on the loop?
How do I program new esserbus Plus detectors and modules into the FlexES panel using Tools 8000 software?
